CLMJM - SILICONE PRIMER MIXTURE

  • MSDS: CLMJM
  • Manufacturer: GE SILICONES
  • Product Name: SILICONE PRIMER MIXTURE
  • National Stock Number: 8040-00-159-4834
Product Identification

Product ID:SILICONE PRIMER MIXTURE
MSDS Date:10/23/1997
FSC:8040
NIIN:00-159-4834
Status Code:A
MSDS Number: CLMJM

Responsible Party
GE SILICONES
260 HUDSON RIVER ROAD
WATERFORD, NY 12188
US

Emergency Phone: 518-237-3330

Info Phone: 518-237-3330

Preparer: ERNEST CARTER

Cage: 01139

Contractor
GENERAL ELECTRIC CO, SILICONE PRODUCTS BUSINESS DEPT
WATERFORD, NY 12188 US

Telephone: 518-237-3330/800-332-3390

Cage: 01139

Ingredients

1-BUTANOL, TITANIUM(4+) SALT

CAS: 5593-70-4

RTECS: XR1585000


TETRAETHYL ORTHOSILICATE

CAS: 78-10-4

RTECS: VV9450000

OSHA PEL 850 MG/M3;100 PPM

ACGIH TLV: 85 MG/M3;10 PPM


ALIPHATIC HYDROCARBON SOLVENT

CAS: 64742-47-8

RTECS: OA5504000


ETHYL SILICATE 40

CAS: 11099-06-2

Hazards

Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Health Hazards Acute and Chronic:INGESTION:HARMFUL IF SWALLOWED.
ASPIRATION CAN BE A HAZARD IF THIS MATERIAL IS SWALLOWED. CAUSES
VOMITING, NAUSEA, DIARRHEA. SKIN CONTACT: MAY CAUSE SKIN DEFATTING
WITH PROLONGED EXPOSURE. MAY CAUSE MODERATE SKIN IRRITATION.
INHALATION: EXCESSIVE INHALATION CAUSES HEADACHE, DIZZINESS,
NAUSEA, INCOORDINATION, CAUSES IRRITATION OF THE MOUTH, NOSE, AND
THROAT. HARMFUL IF INHALED. CAN CAUSE UNCONSCI OUSNESS IF INHALED.
EYE CONTACT: CAUSES SEVERE EYE IRRITATION.VAPOR AND/OR LIQUID
CAUSES IRRITATION. THIS PRODUCT OR ONE OF ITS INGREDIENTS PRESENT
0.1% OR MORE IS NOT LISTED AS A CARCINOGEN OR SUSPEC TED CARCINOGEN
BY NTP, IARC, OR OSHA.
Effects of Overexposure:EYE CONTACT: CAUSES SEVERE EYE IRRITATION.
VAPOR AND/OR LIQUID CAUSES IRRITATION. SUBCHRONIC (TARGET ORGAN)
EFFECTS: RESPIRATORY AILMENTS, CENTRAL NERVOUS SYSTEM DAMAGE,
LIVER/ KIDNEY DAMAGE.
Medical Cond Aggravated by Exposure:RESPIRATORY

First Aid

First Aid:IF SWALLOWED INDUCE VOMITING IMMEDIATELY BY GIVING TWO
GLASSES OF WATER AND STICKING FINGERS DOWN THROAT; NEVER GIVE
ANYTHING TO AN UNCONSCIOUS PERSON. GET MEDICAL ATTENTION. SKIN:
REMOVE CONTAMINATED CLOTHING AND LAUNDER BEFORE REUSE. WASH WITH
SOAP AND WATER. IF INHALED, REMOVE TO FRESH AIR, IF NOT BREATHING
GIVE ARTIFICIAL RESPIRATION, PREFERABLY MOUTH TO MOUTH. IF
BREATHING IS DIFFICULT GIVE O XYGEN. GET MEDICAL ATTENTION.
EYES:IMMEDIATELY FLUSH EYES WITH PLENTY OF WATER FOR AT LEAST 15
MINUTES AND GET MEDICAL ATTENTION IMMEDIATELY AFTER FLUSHING.

Fire Fighting

Flash Point Method:PMCC
Flash Point:=36.7C, 98.F
Autoignition Temp:=245.C, 473.F
Lower Limits:1.0%
Upper Limits:6%
Extinguishing Media:ALL STANDARD FIREFIGHTING MEDIA.
Fire Fighting Procedures:WEAR RESPIRATORY PROTECTION.

Accidental Release

Spill Release Procedures:WIPE, SCRAPE OR SOAK UP INERT MATERIAL AND PUT
IN A CONTAINER FOR DISPOSAL. WEAR PROPER PROTECTIVE EQUIPMENT AS
SPECIFIED IN THE PROTECTIVE EQUIPMENT SECTION. REMOVE SOURCES OF
IGNITION. WARN OTHER WO RKERS OF SPILL. INCREASE AREA VENTILATION.

Handling

Handling and Storage Precautions:USE GROUND STRAP. KEEP CONTAINER
CLOSED WHEN NOT IN USE. AVOID BREATHING VAPORS, IF EXPOSED TO HIGH
VAPOR CONCENTRATION, LEAVE AREA AT ONCE. AVOID CONTACT WITH SKIN
AND EYES. WARNING. FLAMMABLE. DO N OT INHALE VAPORS.

Exposure Controls

Respiratory Protection:USE IN A WELL VENTILATED AREA. USE APPROVED
NIOSH RESPIRATORY PROTECTION IF TLV EXCEEDED OR OVER EXPOSURE IS
LIKELY.
Ventilation:MECHANICAL VENTILATION SHOWERS. EYEWASH STATIONS. USE IN A
WELL VENTILATED AREA.
Protective Gloves:RUBBER GLOVES.
Eye Protection:SAFETY GLASSES.MONOGOGGLES.
Other Protective Equipment:RUBBER APRON.
Work Hygienic Practices:EXHAUST VENTILATION SHOWERS.
Supplemental Safety and Health
EYEWASH STATIONS.

Chemical Properties

Melt/Freeze Pt:=34.C, 93.2F
Vapor Pres:(20 C) (MM HG)
Vapor Density:AIR=1
Spec Gravity:(WATER=1): 0.81
VOC Pounds/Gallon:684
Evaporation Rate & Reference:(BUTYL ACETATE=1): 0.1
Solubility in Water:NEG.
Appearance and Odor:LIQUID PETROLEUM DISTILLATE
Percent Volatiles by Volume:90

Stability

Stability Indicator/Materials to Avoid:YES
CONTACT WITH OXIDIZING AGENTS.
Stability Condition to Avoid:KEEP AWAY FROM HEAT, SPARKS, AND FLAME.
AVOID ANY SOURCE OF IGNITION.
Hazardous Decomposition Products:CARBON MONOXIDE. CARBON DIOXIDE.
SILICON DIOXIDE.
Conditions to Avoid Polymerization:WILL NOT OCCUR.

Disposal

Waste Disposal Methods:DISPOSAL SHOULD BE MADE IN ACCORDANCE WITH
FEDERAL, STATE AND LOCAL REGULATIONS.

Other Information

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.